B M

Rod seal B-M



Properties

Application Hydraulics
Design rod seal
Media Mineral oils, Water emulsions
Material fabric-reinforced NBR
Installation in closed grooves A, in open grooves B
Operating pressure up to 250 bar

Description

Low-friction seal.
Extremely good sealing effect at low pressure.
Simple solution.

Hints

Clearance:
Pressure = 160 bar / e= <0.2
Pressure = 250 bar / e= <0.1
Tolerance: d= H8 / f7; D= H9; L= +0.5 / 0

Article Table

Product Name D mm d mm L mm
Product Name D mm d mm L mm
B 047 019-M 12,00 5,00 6,40
B 051 024-M 13,00 6,00 6,40
B 059 031-M 15,00 8,00 6,40
B 066 039-M 17,00 10,00 6,40
B 075 047-M 19,00 12,00 6,40
B 086 055-M 22,00 14,00 6,40
B 090 059-M 23,00 15,00 6,40
B 094 063-1-M 24,00 16,00 6,40
B 102 070-1-M 26,00 18,00 6,40
B 110 078-1-M 28,00 20,00 6,40
B 118 086-1-M 30,00 22,00 6,40
B 129 098-1-M 33,00 25,00 6,40
B 141 110-M 36,00 28,00 6,40
B 149 118-M 38,00 30,00 6,40
B 157 125-1-M 40,00 32,00 6,40
B 169 137-M 43,00 35,00 6,40
B 1731 41-M 44,00 36,00 6,40
B 188 157-M 48,00 40,00 6,40
B 196 165-M 50,00 42,00 6,40
B 216 177-M 55,00 45,00 8,00
B 236 196-M 60,00 50,00 8,00
B 255 216-1-M 65,00 55,00 8,00
B 259 220-M 66,00 56,00 8,00
B 275 236-M 70,00 60,00 8,00
B 295 248-1-M 75,00 63,00 9,60
B 303 255-M 77,00 65,00 9,60
B 322 275-1-M 82,00 70,00 9,60
B 342 295-M 87,00 75,00 9,60
B 362 314-M 92,00 80,00 9,60
B 381 334-M 97,00 85,00 9,60
B 401 354-M 102,00 90,00 9,60
B 452 393-2-M 115,00 100,00 12,00
B 492 433-M 125,00 110,00 12,00
B 511 452-M 130,00 115,00 12,00
B 551 492-M 140,00 125,00 12,00
B 629 551-2-M 160,00 140,00 16,00
B 669 590-M 170,00 150,00 16,00
B 708 629-1-M 180,00 160,00 16,00
B 787 708-1-M 200,00 180,00 16,00
B 866 787-1-M 220,00 200,00 16,00

Order hints

For special operating conditions (fluid, temperature, pressure ...) please contact us.
Alternative material possible: FPM.

Disclaimer

Despite careful checking, we cannot guarantee the accuracy of all information included on this site, and we accept no liability.
All data and information in our online catalogue are based on currently valid standards and the regulations from the employer's liability insurance association. Product safety can only be guaranteed when our assembly instructions are carefully observed. Non-adherence to these regulations can affect product operation and functioning and result in a loss of warranty. Our warranty is only valid for HANSA-FLEX products. Our products are constantly subject to further development and technical changes are therefore possible.