DDEM

Piston seal DDEM

  • Image_1 Image_1
  • Image_2 Image_2

Properties

Anwendung Hydraulics + pneumatics
Design Piston U-ring
Design Metric
Installation on one-piece pistons A, on multi-part pistons B
Material NBR 75° Shore A
Max. operating pressure up to 80 bar
Media Mineral oil, Water-air
Online-Shop https://shop.hansa-flex.com/de/DDEM
Sliding speed max. 0.5 m/s
Temp. max. 100 °C
Temp. min. -30 °C

Description

Low-friction seal.
Simple solution.

Article Table

Product Name H mm D mm d nom. mm L mm
Product Name H mm D mm d nom. mm L mm
DDEM1206 4.00 mm 12.0 mm 6.00 mm 4.5 mm
DDEM1610 4.00 mm 16.0 mm 10.00 mm 4.5 mm
DDEM2012 5.50 mm 20.0 mm 12.00 mm 6.0 mm
DDEM2517 5.50 mm 25.0 mm 17.00 mm 6.0 mm
DDEM3224 5.50 mm 32.0 mm 24.00 mm 6.0 mm
DDEM4030 7.00 mm 40.0 mm 30.00 mm 7.5 mm
DDEM5040 7.00 mm 50.0 mm 40.00 mm 7.5 mm
DDEM5545 7.00 mm 55.0 mm 45.00 mm 7.5 mm
DDEM6050 7.00 mm 60.0 mm 50.00 mm 7.5 mm
DDEM6353 7.00 mm 63.0 mm 53.00 mm 7.5 mm
DDEM6555 7.00 mm 65.0 mm 55.00 mm 7.5 mm
DDEM7058 8.50 mm 70.0 mm 58.00 mm 9.5 mm
DDEM7563 8.50 mm 75.0 mm 63.00 mm 9.5 mm
DDEM8068 8.50 mm 80.0 mm 68.00 mm 9.5 mm
DDEM8573 8.50 mm 85.0 mm 73.00 mm 9.5 mm
DDEM9078 8.50 mm 90.0 mm 78.00 mm 9.5 mm
DDEM100088 8.50 mm 100.0 mm 88.00 mm 9.5 mm
DDEM105093 8.50 mm 105.0 mm 93.00 mm 9.5 mm
DDEM110098 8.50 mm 110.0 mm 98.00 mm 9.5 mm
DDEM120105 10.00 mm 120.0 mm 105.00 mm 11.0 mm
DDEM125110 10.00 mm 125.0 mm 110.00 mm 11.0 mm
DDEM140125 10.00 mm 140.0 mm 125.00 mm 11.0 mm
DDEM150135 10.00 mm 150.0 mm 135.00 mm 11.0 mm
DDEM160145 10.00 mm 160.0 mm 145.00 mm 11.0 mm
DDEM180160 14.00 mm 180.0 mm 160.00 mm 15.0 mm
DDEM200180 14.00 mm 200.0 mm 180.00 mm 15.0 mm

Order hints

Dichtungen mit Durchmesser 20 bis 510 mm können wir kurzfristig anfertigen.

Disclaimer

Despite careful checking, we cannot guarantee the accuracy of all information included on this site, and we accept no liability.
All data and information in our online catalogue are based on currently valid standards and the regulations from the employer's liability insurance association. Product safety can only be guaranteed when our assembly instructions are carefully observed. Non-adherence to these regulations can affect product operation and functioning and result in a loss of warranty. Our warranty is only valid for HANSA-FLEX products. Our products are constantly subject to further development and technical changes are therefore possible.