DGS H

Rotary fitting, ball bearing



Properties

Connection 1 metric cylindrical outer thread
Connection 2 metric cylindrical outer thread
Construction type Ball bearing
Design Rotary fitting (bulkhead connector)
Construction straight
Sealing form 1 24° inner cone
Sealing form 2 24° inner cone
Scope of supply Socket (without union nut and cutting ring)
Surface electro galvanised
Material Steel

Hints

Information about fitting, installation, pressure loads and permissible operating temperatures can be found in the technical information for pipe fittings.

Article Table

Product Name Series Operating pressure Ø d2 mm G1 L1 mm L2 mm L3 mm L4 mm L5 mm L6 mm S1 S2 S3
Product Name Series Operating pressure Ø d2 mm G1 L1 mm L2 mm L3 mm L4 mm L5 mm L6 mm S1 S2 S3
DGS NW 06 HL L PN 315 8 M 14 x 1.5 40,0 16,0 5 10 37,0 23,0 19 22 17
DGS NW 08 HL L PN 315 10 M 16 x 1.5 50,0 16,0 5 11 46,0 23,0 24 30 22
DGS NW 10 HL L PN 315 12 M 18 x 1.5 50,0 16,0 5 11 46,0 23,0 24 30 24
DGS NW 13 HL L PN 315 15 M 22 x 1.5 51,0 19,0 5 12 46,0 26,0 24 30 30
DGS NW 16 HL L PN 315 18 M 26 x 1.5 61,0 28,0 15 12 56,5 35,5 36 41 36
DGS NW 20 HL L PN 160 22 M 30 x 2 63,0 30,5 15 14 56,5 38,0 36 41 41
DGS NW 25 HL L PN 160 28 M 36 x 2 75,0 31,0 15 14 68,5 38,5 55 60 46
DGS NW 32 HL L PN 160 35 M 45 x 2 74,0 31,5 15 16 68,5 42,0 55 60 55
DGS NW 04 HS H S PN 500 8 M 16 x 1.5 42,0 16,0 5 12 37,0 23,0 19 22 22
DGS NW 08 HS H S PN 500 12 M 20 x 1.5 52,5 15,5 5 12 48,0 23,0 24 30 27
DGS NW 13 HS H S PN 400 16 M 24 x 1.5 51,5 17,5 5 14 46,0 26,0 24 30 32
DGS NW 16 HS H S PN 400 20 M 30 x 2 65,5 28,5 15 16 60,0 39,0 36 41 41
DGS NW 20 HS H S PN 400 25 M 36 x 2 66,0 30,0 15 18 60,0 42,0 36 41 46
DGS NW 25 HS H S PN 400 30 M 42 x 2 75,5 30,5 15 22 69,0 44,0 55 60 50
Series: LL = Very light L = Light S = Heavy - PN = Nominal pressure PB = Max. operating pressure - Ø d2 = External pipe diameter

Disclaimer

Despite careful checking, we cannot guarantee the accuracy of all information included on this site, and we accept no liability.
All data and information in our online catalogue are based on currently valid standards and the regulations from the employer's liability insurance association. Product safety can only be guaranteed when our assembly instructions are carefully observed. Non-adherence to these regulations can affect product operation and functioning and result in a loss of warranty. Our warranty is only valid for HANSA-FLEX products. Our products are constantly subject to further development and technical changes are therefore possible.