DMO 45

Fitting, double nuts, angle 45°

  • Image_1 Image_1
  • Image_2 Image_2

Properties

Connection 1 + 2 metric nut thread
Construction Angle 45°
Design Fitting, double nuts
Material Steel
Sealing form 1 + 2 24° outer cone with O-ring
Standard DIN 2353
ISO 8434-1
Surface electro galvanised

Hints

Information about fitting, installation, pressure loads and permissible operating temperatures can be found in the technical information for pipe fittings.

Article Table

Product Name L1 mm S1 OR Operating pressure Ø d mm AF mm G1 Series
Product Name L1 mm S1 OR Operating pressure Ø d mm AF mm G1 Series
DMO 45 NW 04 L 22.5 14 4.0 x 1.5 PN 400 6 14 M 12 x 1,5 L
DMO 45 NW 06 L 23.0 17 6.0 x 1.5 PN 400 8 14 M 14 x 1.5 L
DMO 45 NW 08 L 25.0 19 7.5 x 1.5 PN 400 10 19 M 16 x 1.5 L
DMO 45 NW 10 L 25.5 22 9.0 x 1.5 PN 400 12 19 M 18 x 1.5 L
DMO 45 NW 13 L 27.0 27 12.0 x 2.0 PN 400 15 22 M 22 x 1.5 L
DMO 45 NW 16 L 30.0 32 15.0 x 2.0 PN 315 18 27 M 26 x 1.5 L
DMO 45 NW 20 L 32.0 36 20.0 x 2.0 PN 315 22 30 M 30 x 2 L
DMO 45 NW 25 L 35.0 41 26.0 x 2.0 PN 250 28 36 M 36 x 2 L
DMO 45 NW 32 L 39.5 50 32.0 x 2.5 PN 250 35 50 M 45 x 2 L
DMO 45 NW 40 L 42.0 60 38.0 x 2.5 PN 250 42 50 M 52 x 2 L
DMO 45 NW 03 S 23.5 17 4.0 x 1.5 PN 630 6 14 M 14 x 1.5 S
DMO 45 NW 04 S 26.5 19 6.0 x 1.5 PN 630 8 19 M 16 x 1.5 S
DMO 45 NW 06 S 27.0 22 7.5 x 1.5 PN 630 10 19 M 18 x 1.5 S
DMO 45 NW 08 S 27.5 24 9.0 x 1.5 PN 630 12 19 M 20 x 1.5 S
DMO 45 NW 13 S 31.5 30 12.0 x 2.0 PN 400 16 27 M 24 x 1.5 S
DMO 45 NW 16 S 36.0 36 16.3 x 2.4 PN 400 20 30 M 30 x 2 S
DMO 45 NW 20 S 40.5 46 20.3 x 2.4 PN 400 25 36 M 36 x 2 S
DMO 45 NW 25 S 44.5 50 25.3 x 2.4 PN 400 30 50 M 42 x 2 S
DMO 45 NW 32 S 50.5 60 33.3 x 2.4 PN 315 38 50 M 52 x 2 S
Series: LL = Very light L = Light S = Heavy
PN = Nominal pressure
Ø d = External pipe diameter
SW, S1, S2, S3 = With across flats

Disclaimer

Despite careful checking, we cannot guarantee the accuracy of all information included on this site, and we accept no liability.
All data and information in our online catalogue are based on currently valid standards and the regulations from the employer's liability insurance association. Product safety can only be guaranteed when our assembly instructions are carefully observed. Non-adherence to these regulations can affect product operation and functioning and result in a loss of warranty. Our warranty is only valid for HANSA-FLEX products. Our products are constantly subject to further development and technical changes are therefore possible.