DPC

Piston packing set for split pistons DPC

  • Image_1 Image_1
  • Image_2 Image_2

Properties

Anwendung Hydraulics
Design Piston packing set
Installation on multi-part pistons
Material (3) Back ring: acetal resin, (2) Guide ring: acetal resin, (1) Seal: fabric-reinforced NBR
Max. operating pressure up to 700 bar
Media Mineral oil, Water emulsions
Sliding speed max. 0.5 m/s
Temp. max. 110 °C
Temp. min. -30 °C

Description

Extremely good sealing effect at low pressure.
Low friction.
High pressure.
Simple solution.

Article Table

Product Name D mm G mm P mm M mm d mm L mm
Product Name D mm G mm P mm M mm d mm L mm
DPC4024 40 mm 6.35 mm 38.70 mm 35.40 mm 24 mm 18.4 mm
DPC4529 45 mm 6.35 mm 43.70 mm 40.40 mm 29 mm 18.4 mm
DPC5034 50 mm 6.35 mm 48.70 mm 45.40 mm 34 mm 18.4 mm
DPC5539 55 mm 6.35 mm 53.70 mm 50.40 mm 39 mm 18.4 mm
DPC6044 60 mm 6.35 mm 58.70 mm 55.40 mm 44 mm 18.4 mm
DPC6550 65 mm 6.35 mm 63.70 mm 60.40 mm 50 mm 18.4 mm
DPC7050 70 mm 6.35 mm 68.30 mm 64.20 mm 50 mm 22.4 mm
DPC7555 75 mm 6.35 mm 73.30 mm 69.20 mm 55 mm 22.4 mm
DPC8060 80 mm 6.35 mm 78.30 mm 74.20 mm 60 mm 22.4 mm
DPC8565 85 mm 6.35 mm 83.30 mm 79.20 mm 65 mm 22.4 mm
DPC9070 90 mm 6.35 mm 88.30 mm 84.15 mm 70 mm 22.4 mm
DPC9575 95 mm 6.35 mm 93.30 mm 89.15 mm 75 mm 22.4 mm
DPC10075 100 mm 6.35 mm 98.05 mm 93.15 mm 75 mm 22.4 mm
DPC10080 100 mm 6.35 mm 98.30 mm 94.15 mm 80 mm 25.4 mm
DPC10585 105 mm 6.35 mm 103.00 mm 98.10 mm 85 mm 22.4 mm
DPC11085 110 mm 6.35 mm 108.00 mm 103.10 mm 85 mm 22.4 mm
DPC120100 120 mm 6.35 mm 118.30 mm 114.10 mm 100 mm 25.4 mm
DPC140115 140 mm 6.35 mm 138.00 mm 133.00 mm 115 mm 25.4 mm
DPC150125 150 mm 6.35 mm 148.00 mm 143.00 mm 125 mm 25.4 mm

Order hints

Anderer Werkstoff möglich: FPM, Bei besonderen Betriebsbedingungen (Flüssigkeit, Temperatur, Druck ...) wenden Sie sich bitte an uns.

Disclaimer

Despite careful checking, we cannot guarantee the accuracy of all information included on this site, and we accept no liability.
All data and information in our online catalogue are based on currently valid standards and the regulations from the employer's liability insurance association. Product safety can only be guaranteed when our assembly instructions are carefully observed. Non-adherence to these regulations can affect product operation and functioning and result in a loss of warranty. Our warranty is only valid for HANSA-FLEX products. Our products are constantly subject to further development and technical changes are therefore possible.