DPS

Piston packing set for one-piece pistons DPS

  • Image_1 Image_1
  • Image_2 Image_2

Properties

Application Hydraulics
Design Piston packing set
Installation on one-piece pistons A
on multi-part pistons B
Material (2) Guide ring: acetal resin
(1) Seal: fabric-reinforced NBR
Media Mineral oil
Water emulsions
Operating pressure 300 bar
Sliding speed max. 0.5 m/s
Temp. max. 110 °C
Temp. min. -30 °C

Description

Low-friction seal.
Simple solution.

Article Table

Product Name D mm L mm G mm P mm d mm M mm Standard grooves
Product Name D mm L mm G mm P mm d mm M mm Standard grooves
DPS 25 17-1 25 10.0 4.00 24.0 17 22 ISO 5597
DPS 32 24-1 32 10.0 4.00 31.0 24 29 ISO 5597
DPS 32 24 32 15.5 3.20 31.4 24 28 -
DPS 35 27 35 15.5 3.20 34.4 27 31 -
DPS 40 32-1 40 10.0 4.00 39.0 32 37 ISO 5597
DPS 40 32 40 15.5 3.20 39.4 32 36 -
DPS 45 37 45 15.5 3.20 44.4 37 41 -
DPS 50 38 50 20.5 4.20 49.4 38 46 -
DPS 50 40-1 50 12.5 4.00 49.0 40 47 ISO 5597
DPS 60 48 60 20.5 4.20 59.4 48 56 -
DPS 63 51 63 20.5 4.20 62.4 51 59 -
DPS 63 53-1 63 12.5 4.00 62.0 53 60 ISO 5597
DPS 65 53 65 20.5 4.20 64.4 53 61 -
DPS 70 58 70 20.5 4.20 69.4 58 66 -
DPS 75 63 75 20.5 4.20 74.4 63 71 -
DPS 80 65-1 80 20.0 5.00 78.5 65 76 ISO 5597
DPS 80 66 80 22.5 5.20 79.4 66 76 -
DPS 85 71 85 22.5 5.20 84.4 71 81 -
DPS 90 76 90 22.5 5.20 89.4 76 86 -
DPS 100 86 100 22.5 5.20 99.4 86 96 -
DPS 110 96 110 22.5 5.20 109.4 96 106 -
DPS 120 106 120 22.5 5.20 119.4 106 116 -
DPS 125 105-1 125 25.0 6.30 123.0 105 120 ISO 5597
DPS 125 108 125 26.5 7.20 124.4 108 121 -
DPS 140 120-1 140 25.0 6.30 138.0 120 135 ISO 5597
DPS 140 123 140 26.5 7.20 139.4 123 136 -
DPS 160 140-1 160 25.0 6.30 158.0 140 155 ISO 5597
DPS 160 143 160 26.5 7.20 159.4 143 156 -
DPS 180 163 180 26.5 7.20 179.4 163 176 -
DPS 200 180 200 31.5 9.20 199.4 180 196 -
DPS 220 200 220 31.5 9.20 219.4 200 216 -
DPS 250 230 250 31.5 9.20 249.4 230 246 -

Order hints

Alternative material possible: FPM.
For special operating conditions (fluid, temperature, pressure ...) please contact us.

Disclaimer

Despite careful checking, we cannot guarantee the accuracy of all information included on this site, and we accept no liability.
All data and information in our online catalogue are based on currently valid standards and the regulations from the employer's liability insurance association. Product safety can only be guaranteed when our assembly instructions are carefully observed. Non-adherence to these regulations can affect product operation and functioning and result in a loss of warranty. Our warranty is only valid for HANSA-FLEX products. Our products are constantly subject to further development and technical changes are therefore possible.