EUS-I

Rod seal EUS-I



Properties

Application Hydraulics
Design rod seal
Media Mineral oils
Material (1) Pre-load ring: NBR, (2) Seal: PUR
Installation in closed grooves A, in open grooves B
Operating pressure up to 400 bar

Description

Extremely good sealing effect at low pressure.
High abrasion resistance.
Simple solution.

Hints

Clearance:
pressure = 50 bar / e= d < 60 <0.40 / e= d > 60 <0.50
Pressure= 100 bar / e= d < 60 <0.30 / e= d > 60 <0.40
Pressure = 200 bar / e= d < 60 <0.20 / e= d > 60 <0.30
Pressure = 300 bar / e= d < 60 <0.15 / e= d > 60 <0.20
Pressure = 400 bar / e= d < 60 <0.10 / e= d > 60 <0.15
Tolerance: d= H8 / f7; D= H9; L= +0.2 / 0

Article Table

Product Name d mm D mm L mm
Product Name d mm D mm L mm
EUS-I 025 050 6,35 12,70 3,5
EUS-I 050 075 12,70 19,05 3,5
EUS-I 050 100 12,70 25,40 10,5
EUS-I 075 100-2 19,05 25,40 3,5
EUS-I 075 100 19,05 25,40 5,3
EUS-I 075 100-1 19,05 25,40 7,0
EUS-I 087 112 22,22 28,57 7,0
EUS-I 100 125 25,40 31,75 5,3
EUS-I 100 137 25,40 34,93 8,7
EUS-I 112 137 28,57 34,93 3,5
EUS-I 112 150 28,57 38,10 8,7
EUS-I 125 150 31,75 38,10 5,3
EUS-I 125 150-1 31,75 38,10 7,0
EUS-I 125 162 31,75 41,27 7,0
EUS-I 125 162-1 31,75 41,27 8,7
EUS-I 125 175 31,75 44,45 5,3
EUS-I 125 187 31,75 47,62 8,7
EUS-I 125 187-1 31,75 47,62 10,5
EUS-I 125 200 31,75 50,80 10,5
EUS-I 137 162 34,92 41,27 5,3
EUS-I 137 175 34,92 44,45 8,7
EUS-I 150 187 38,10 47,62 7,0
EUS-I 162 200 41,27 50,80 10,5
EUS-I 175 212 44,45 53,97 7,0
EUS-I 175 212-2 44,45 53,97 8,7
EUS-I 175 212-1 44,45 53,97 10,5
EUS-I 175 225 44,45 57,15 10,5
EUS-I 175 237 44,45 60,32 14,0
EUS-I 187 225 47,62 57,15 5,3
EUS-I 187 225-1 47,62 57,15 10,5
EUS-I 187 237 47,62 60,32 10,5
EUS-I 187 250 47,62 63,50 10,5
EUS-I 200 237 50,80 60,32 8,7
EUS-I 200 237-1 50,80 60,32 10,5
EUS-I 200 250 50,80 63,50 10,5
EUS-I 212 250 53,97 63,50 7,0
EUS-I 212 250-1 53,97 63,50 10,5
EUS-I 225 262-2 57,15 66,67 5,3
EUS-I 225 262 57,15 66,67 8,7
EUS-I 225 262-1 57,15 66,67 10,5
EUS-I 225 275 57,15 69,85 10,5
EUS-I 250 287 63,50 73,02 8,7
EUS-I 250 287-1 63,50 73,02 10,5
EUS-I 250 300 63,50 76,20 7,0
EUS-I 250 300-1 63,50 76,20 10,5
EUS-I 250 312 63,50 79,37 14,0
EUS-I 262 300 66,67 76,20 5,3
EUS-I 262 300-1 66,67 76,20 10,5
EUS-I 275 325 69,85 82,55 10,5
EUS-I 275 350 69,85 88,90 10,5
EUS-I 275 350-1 69,85 88,90 17,5
EUS-I 287 337 73,02 85,72 10,5
EUS-I 287 350 73,02 88,90 14,0
EUS-I 300 337-1 76,20 85,72 10,5
EUS-I 300 350 76,20 88,90 10,5
EUS-I 300 362 76,20 92,07 10,5
EUS-I 300 362-1 76,20 92,07 14,0
EUS-I 300 375 76,20 95,25 17,5
EUS-I 312 350 79,37 88,90 10,5
EUS-I 312 362 79,37 92,07 10,5
EUS-I 325 375 82,55 95,25 10,5
EUS-I 325 375-1 82,55 95,25 14,0
EUS-I 325 400 82,55 101,60 14,0
EUS-I 350 400 88,90 101,60 10,5
EUS-I 350 450 88,90 114,30 21,0
EUS-I 375 425 95,25 107,95 10,5
EUS-I 375 425-1 95,25 107,95 15,7
EUS-I 375 450 95,25 114,30 14,0
EUS-I 400 450 101,60 114,30 10,5
EUS-I 400 450-1 101,60 114,30 15,7
EUS-I 500 550 127,00 139,70 10,5
EUS-I 550 625 139,70 158,75 17,5

Order hints

We are able to produce EUS-I seals with diameters of 20 to 510 mm with short lead times.

Disclaimer

Despite careful checking, we cannot guarantee the accuracy of all information included on this site, and we accept no liability.
All data and information in our online catalogue are based on currently valid standards and the regulations from the employer's liability insurance association. Product safety can only be guaranteed when our assembly instructions are carefully observed. Non-adherence to these regulations can affect product operation and functioning and result in a loss of warranty. Our warranty is only valid for HANSA-FLEX products. Our products are constantly subject to further development and technical changes are therefore possible.