FH (3000 PSI)

SAE flange half



Properties

Design SAE flange half
Construction straight
Mounting Screw bore hole
Scope of supply flange only
Standard ISO 6162-1, SAE J518
Surface electro galvanised
Material S355J2G3 (ST52.3)

Hints

Recommended screws are listed in the columns M (metr) and M (unc).

Article Table

Product Name PB 10.9 bar Size A mm B mm C mm D mm E mm F mm G mm H mm I mm L mm M metr. M unc
Product Name PB 10.9 bar Size A mm B mm C mm D mm E mm F mm G mm H mm I mm L mm M metr. M unc
FH 3001 350 1/2" 31,0 24,3 38,1 54 8,7 22,8 19 13 6,2 8,7 M 8 x 25 5/16" x 1.1/4"
FH 3002 350 3/4" 38,9 32,1 47,6 65 11,1 25,9 22 14 6,2 10,7 M 10 x 30 3/8" x 1.1/4"
FH 3003 315 1" 45,2 38,5 52,4 70 13,1 29,2 24 16 7,5 10,7 M 10 x 30 3/8" x 1.1/4"
FH 3004 250 1.1/4" 51,6 43,7 58,7 79 15,1 36,3 22 16 7,5 12,0 M 10 x 30 7/16" x 1.1/2"
FH 3014 250 1.1/4" 51,6 43,7 58,7 79 15,1 36,3 22 16 7,5 10,7 M 10 x 30 -
FH 3044 250 1.1/4" 51,6 43,7 58,7 79 15,1 36,3 22 16 7,5 12,7 M 12 x 35 -
FH 3005 200 1.1/2" 61,1 50,8 69,9 94 17,9 41,1 25 16 7,5 13,5 M 12 x 35 1/2" x 1.1/2"
FH 3006 200 2" 72,2 62,7 77,8 102 21,4 48,2 26 16 9,0 13,5 M 12 x 35 1/2" x 1.1/2"
FH 3007 160 2.1/2" 84,9 74,9 88,9 114 25,4 54,1 38 19 9,0 13,5 M 12 x 40 1/2" x 1.1/2"
FH 3008 160 3" 102,4 90,9 106,4 135 31,0 65,3 41 22 9,0 17,0 M 16 x 50 5/8" x 2"
FH 3009 35 3.1/2" 115,1 102,4 120,7 152 34,9 69,5 28 22 10,7 17,0 M 16 x 50 5/8" x 2"
FH 3010 35 4" 127,8 115,1 130,2 162 38,9 76,0 35 25 10,7 17,0 M 16 x 50 5/8" x 2"
FH 3011 35 5" 153,2 140,5 152,4 184 46,0 90,0 41 28 10,7 17,0 M 16 x 55 5/8" x 2"
PN = Nominal pressure PB = Max. operating pressure - Series: LL = Very light L = Light S = Heavy - Ø = External pipe diameter

Disclaimer

Despite careful checking, we cannot guarantee the accuracy of all information included on this site, and we accept no liability.
All data and information in our online catalogue are based on currently valid standards and the regulations from the employer's liability insurance association. Product safety can only be guaranteed when our assembly instructions are carefully observed. Non-adherence to these regulations can affect product operation and functioning and result in a loss of warranty. Our warranty is only valid for HANSA-FLEX products. Our products are constantly subject to further development and technical changes are therefore possible.