Properties

Application Hydraulics
Design Wipers
Installation is pressed into an open groove
Material (1) Sleeve: Steel
(2) Wiper: NBR 90° Shore A
Media Mineral oil
Water emulsions
Sliding speed max. 0.5 m/s
Temp. max. 100 °C
Temp. min. -30 °C

Description

Low spatial requirement.
No penetration of dirt via the outer metal ring.
Simple solution.

Article Table

Product Name H mm D mm d mm L mm Standard grooves
Product Name H mm D mm d mm L mm Standard grooves
GA 10 16-3 4.5 16.0 10 3.0 -
GA 10 19-3 5.0 18.9 10 2.9 -
GA 10 20-5 8.0 20.0 10 5.0 -
GA 12 18-3 5.0 18.0 12 3.5 -
GA 12 20-4 6.0 20.0 12 4.0 -
GA 12 22-5 8.0 22.0 12 5.0 -
GA 14 20-3 4.5 20.0 14 3.0 -
GA 14 22-3 4.0 22.0 14 3.0 -
GA 16 22-3 4.0 22.0 16 3.0 -
GA 16 26-5 8.0 26.0 16 5.0 -
GA 18 28-5 7.0 28.0 18 5.0 -
GA 18 28-7 10.0 28.0 18 7.0 ISO 5597
GA 20 26-3 5.0 26.0 20 3.5 -
GA 20 28-3 5.0 28.0 20 3.5 -
GA 20 28-5 7.0 28.0 20 5.0 -
GA 20 30-4 6.0 30.0 20 4.0 -
GA 20 30-5 8.0 30.0 20 5.0 -
GA 20 30-7 10.0 30.0 20 7.0 ISO 5597
GA 20 35-7 10.0 35.0 20 7.0 -
GA 22 28-5 9.0 28.0 22 5.0 -
GA 22 30-4 7.0 30.0 22 4.0 -
GA 22 32-5 7.0 32.0 22 5.0 -
GA 22 32-7 10.0 32.0 22 7.0 ISO 5597
GA 22 35-5 8.0 35.0 22 5.0 -
GA 25 35-5 8.0 35.0 25 5.0 -
GA 25 35-7 10.0 35.0 25 7.0 ISO 5597
GA 28 38-5 8.0 38.0 28 5.0 -
GA 28 38-7 10.0 38.0 28 7.0 -
GA 28 40-7 10.0 40.0 28 7.0 -
GA 30 40-5 8.0 40.0 30 5.0 -
GA 30 40-7 10.0 40.0 30 7.0 -
GA 30 45-5 8.0 45.0 30 5.0 -
GA 32 40-4 7.0 40.0 32 4.0 -
GA 32 42-5 7.0 42.0 32 5.0 -
GA 32 42-7 10.0 42.0 32 7.0 -
GA 32 45-4 8.0 45.0 32 4.0 -
GA 32 45-7 10.0 45.0 32 7.0 -
GA 33 43-5 8.0 43.0 33 5.0 -
GA 35 45-5 8.0 45.0 35 5.0 -
GA 35 45-7 10.0 45.0 35 7.0 ISO 5597
GA 35 47-7 10.0 47.0 35 7.0 -
GA 36 45-7 10.0 45.0 36 7.0 -
GA 36 46-5 8.0 46.0 36 5.0 -
GA 38 48-7 10.0 48.0 38 7.0 -
GA 40 50-5 8.0 50.0 40 5.0 -
GA 40 50-7 10.0 50.0 40 7.0 ISO 5597
GA 40 52-5 8.0 52.0 40 5.0 -
GA 42 52-7 10.0 52.0 42 7.0 -
GA 45 55-7 10.0 55.0 45 7.0 ISO 5597
GA 45 60-7 10.0 60.0 45 7.0 -
GA 48 60-7 10.0 60.0 48 7.0 -
GA 50 56-5 8.0 56.0 50 5.0 -
GA 50 60-5 8.0 60.0 50 5.0 -
GA 50 60-7 10.0 60.0 50 7.0 ISO 5597
GA 50 65-5 8.0 65.0 50 5.0 -
GA 50 65-7 10.0 65.0 50 7.0 -
GA 52 62-7 10.0 62.0 52 7.0 -
GA 55 63-7 10.0 63.0 55 7.0 -
GA 55 65-7 10.0 65.0 55 7.0 -
GA 55 70-7 10.0 70.0 55 7.0 -
GA 55 80-5 8.0 80.0 55 5.0 -
GA 56 65-7 10.0 65.0 56 7.0 -
GA 56 66-5 8.0 66.0 56 5.0 -
GA 56 66-7 10.0 66.0 56 7.0 ISO 5597
GA 60 70-5 7.0 70.0 60 5.0 -
GA 60 70-7 10.0 70.0 60 7.0 -
GA 60 74-5 8.0 74.0 60 5.0 -
GA 60 75-7 10.0 75.0 60 7.0 -
GA 63 75-7 10.0 75.0 63 7.0 -
GA 63 83-5 8.0 83.0 63 5.0 -
GA 65 75-7 10.0 75.0 65 7.0 -
GA 70 80-5 7.0 80.0 70 5.0 -
GA 70 80-7 10.0 80.0 70 7.0 ISO 5597
GA 75 85-7 10.0 85.0 75 7.0 -
GA 75 87-5 7.0 87.0 75 5.0 -
GA 80 90-7 10.0 90.0 80 7.0 ISO 5597
GA 85 95-7 10.0 95.0 85 7.0 -
GA 90 100-5 7.0 100.0 90 5.0 -
GA 90 100-7 10.0 100.0 90 7.0 ISO 5597
GA 95 105-7 10.0 105.0 95 7.0 -
GA 100 110-5 7.0 110.0 100 5.0 -
GA 100 110-7 10.0 110.0 100 7.0 -
GA 105 115-7 10.0 115.0 105 7.0 -
GA 110 120-7 10.0 120.0 110 7.0 -
GA 115 125-7 10.0 125.0 115 7.0 -
GA 120 130-7 10.0 130.0 120 7.0 -
GA 125 140-7 10.0 140.0 125 7.0 -
GA 125 140-9 12.0 140.0 125 9.0 ISO 5597
GA 130 145-9 12.0 145.0 130 9.0 -
GA 135 145-7 10.0 145.0 135 7.0 -
GA 135 150-9 12.0 150.0 135 9.0 -
GA 140 150-7 10.0 150.0 140 7.0 -
GA 140 155-9 12.0 155.0 140 9.0 ISO 5597
GA 150 165-9 12.0 165.0 150 9.0 -
GA 160 175-9 12.0 175.0 160 9.0 ISO 5597
GA 170 185-10 14.0 185.0 170 10.0 -
GA 180 195-10 14.0 195.0 180 10.0 -
GA 200 220-12 16.0 220.0 200 12.0 -

Order hints

Alternative material possible: FPM.
For special operating conditions (fluid, temperature, pressure ...) please contact us.

Disclaimer

Despite careful checking, we cannot guarantee the accuracy of all information included on this site, and we accept no liability.
All data and information in our online catalogue are based on currently valid standards and the regulations from the employer's liability insurance association. Product safety can only be guaranteed when our assembly instructions are carefully observed. Non-adherence to these regulations can affect product operation and functioning and result in a loss of warranty. Our warranty is only valid for HANSA-FLEX products. Our products are constantly subject to further development and technical changes are therefore possible.