GPS

Piston packing set, GPS



Properties

Application Hydraulics
Design Piston packing set
Media Mineral oils
Material (1) Dynamic seal: PUR, (2) Static seal: NBR
Installation on multi-part pistons B, on one-piece pistons A
Operating pressure up to 400 bar

Description

Easy assembly.
Low spatial requirement.
Extremely good sealing effect.
High abrasion resistance.

Hints

Clearance:
Pressure = 50 bar / e max.= 1.20
Pressure = 100 bar / e max.= 0.80
Pressure = 200 bar / e max.= 0.40
Pressure = 300 bar / e max.= 0.25
Pressure= 400 bar / e max.= <0.15
Tolerance: D= H9; d= +0,1/0; L= +0.2/0

Article Table

Product Name D mm d mm L mm Standard grooves
Product Name D mm d mm L mm Standard grooves
GPS 25 25 14,0 4,2 ISO 5597
GPS 25-1 25 17,5 3,2 ISO 5597
GPS 30 30 22,5 3,2 ISO 5597
GPS 32 32 21,0 4,2 ISO 5597
GPS 32-1 32 24,5 3,2 ISO 5597
GPS 35 35 27,5 3,2 -
GPS 40 40 24,5 6,3 -
GPS 40-1 40 29,0 4,2 ISO 5597
GPS 40-2 40 32,5 3,2 -
GPS 45 45 29,5 6,3 -
GPS 45-1 45 34,0 4,2 -
GPS 49 49 38,0 4,2 -
GPS 50 50 34,5 6,3 ISO 5597
GPS 50-1 50 39,0 4,2 ISO 5597
GPS 55 55 39,5 6,3 -
GPS 55-1 55 44,0 4,2 -
GPS 60 60 44,5 6,3 -
GPS 60-1 60 49,0 4,2 -
GPS 63 63 47,5 6,3 ISO 5597
GPS 63-1 63 52,0 4,2 ISO 5597
GPS 65 65 49,5 6,3 -
GPS 65-1 65 54,0 4,2 -
GPS 70 70 54,5 6,3 -
GPS 70-1 70 59,0 4,2 -
GPS 75 75 59,5 6,3 -
GPS 75-1 75 64,0 4,2 -
GPS 80 80 64,5 6,3 -
GPS 80-1 80 69,0 4,2 -
GPS 85 85 69,5 6,3 -
GPS 90 90 74,5 6,3 -
GPS 100 100 84,5 6,3 ISO 5597
GPS 105 105 89,5 6,3 -
GPS 110 110 94,5 6,3 -
GPS 120 120 104,5 6,3 -
GPS 125 125 109,5 6,3 ISO 5597
GPS 130 130 114,5 6,3 -
GPS 140 140 119,0 8,1 -
GPS 150 150 129,0 8,1 -
GPS 160 160 139,0 8,1 ISO 5597
GPS 170 170 149,0 8,1 -
GPS 180 180 159,0 8,1 -
GPS 200 200 179,0 8,1 ISO 5597

Order hints

We are able to produce seals with diameters of 20 to 510 mm with short lead times.

Disclaimer

Despite careful checking, we cannot guarantee the accuracy of all information included on this site, and we accept no liability.
All data and information in our online catalogue are based on currently valid standards and the regulations from the employer's liability insurance association. Product safety can only be guaranteed when our assembly instructions are carefully observed. Non-adherence to these regulations can affect product operation and functioning and result in a loss of warranty. Our warranty is only valid for HANSA-FLEX products. Our products are constantly subject to further development and technical changes are therefore possible.