I-DWR

Rod guide I-DWR



Properties

Media Mineral oils, Water emulsions
Material acetal resin + glass fibre
Surface pressure at 20°C 15 N/mm2; at 100°C 10 N/mm3
Installation insert into the groove

Description

Easy working of the fitting groove and assembly.
High load-bearing capacity.
Low coefficient of wear and low coefficient of friction (between 0.05 and 0.1) available in many sizes.

Hints

Calculation of shear force; F= p x D x L x n
F= maximum shear force (N)
p = maximum surface pressure (N/mm2)
D x L= projected area (mm2)
n= quantity of rings

Article Table

Product Name D mm d mm L mm
Product Name D mm d mm L mm
I-DWR 18-2-9.6 22 18 9,60
I-DWR 20-2-9.6 24 20 9,60
I-DWR 25-2-9.6 29 25 9,60
I-DWR 28-2-9.6 32 28 9,60
I-DWR 30-2-9.6 34 30 9,60
I-DWR 30-3-9.6 36 30 9,60
I-DWR 32-2-9.6 36 32 9,60
I-DWR 32-3-10 38 32 10,00
I-DWR 34-2-9.6 38 34 9,60
I-DWR 35-2-9.6 39 35 9,60
I-DWR 35-2-12.8 39 35 12,80
I-DWR 35-3-9.6 41 35 9,60
I-DWR 36-2-9.6 40 36 9,60
I-DWR 36-3-9.6 42 36 9,60
I-DWR 38-2-9.6 42 38 9,60
I-DWR 38-2-18 42 38 18,00
I-DWR 40-2-9.6 44 40 9,60
I-DWR 40-3-9.6 46 40 9,60
I-DWR 40-3-12.8 46 40 12,80
I-DWR 42-3-9.6 48 42 9,60
I-DWR 44-3-9.6 50 44 9,60
I-DWR 45-3-9.6 51 45 9,60
I-DWR 45-3-12.8 51 45 12,80
I-DWR 48-3-9.6 54 48 9,60
I-DWR 50-3-9.6 56 50 9,60
I-DWR 50-3-12.8 56 50 12,80
I-DWR 53-3-9.6 59 53 9,60
I-DWR 55-3-9.6 61 55 9,60
I-DWR 55-3-12.8 61 55 12,80
I-DWR 56-3-12.8 62 56 12,80
I-DWR 60-3-12.8 66 60 12,80
I-DWR 63-3-12.8 69 63 12,80
I-DWR 65-3-12.8 71 65 12,80
I-DWR 70-3-12.8 76 70 12,80
I-DWR 75-3-12.8 81 75 12,80
I-DWR 75-3-19.2 81 75 19,20
I-DWR 76-3-12.8 82 76 12,80
I-DWR 78-3-25 84 78 25,00
I-DWR 80-3-12.8 96 80 12,80
I-DWR 90-3-12.8 96 90 12,80
I-DWR 100-3-12.8 106 100 12,80
I-DWR 105-3-12.8 111 105 12,80
I-DWR 105-3-19.2 111 105 19,20
I-DWR 110-3-12.8 116 110 12,80
I-DWR 110-3-25.75 116 110 25,75
I-DWR 115-3-12.8 121 115 12,80
I-DWR 125-3-12.8 131 125 12,80
I-DWR 130-3-12.8 136 130 12,80
I-DWR 145-3-12.8 151 145 12,80
I-DWR 160-3-19.2 166 160 19,20
I-DWR 200-3-19.2 206 200 19,20

Order hints

We are able to produce guide rings with diameters of 20 to 510 mm with short lead times.

Disclaimer

Despite careful checking, we cannot guarantee the accuracy of all information included on this site, and we accept no liability.
All data and information in our online catalogue are based on currently valid standards and the regulations from the employer's liability insurance association. Product safety can only be guaranteed when our assembly instructions are carefully observed. Non-adherence to these regulations can affect product operation and functioning and result in a loss of warranty. Our warranty is only valid for HANSA-FLEX products. Our products are constantly subject to further development and technical changes are therefore possible.