SRS 1-5 D PA

Pipe clamp, double pipes



Properties

Construction type Inside of clamp with web
Design Double pipe clamp
Standard DIN 3015-3
Material Polyamide 6

Description

Webs in the inner surface of the clamps dampen impacts and vibrations and absorb forces along the pipe axis.
A gap between the two halves pretensions the pipe.

Hints

The use of clamps with a smooth inner surface is recommended for retaining hoses and cables. No pretension is applied when fitting and the block height H is reduced to the gap width S1.

Article Table

Product Name Clamp size External pipe Ø d2 mm External pipe Ø d2 a mm B mm H mm L mm S1 mm
Product Name Clamp size External pipe Ø d2 mm External pipe Ø d2 a mm B mm H mm L mm S1 mm
SRS 106.4 D PA 1 6,4 1/4" 20 30 27 36 1,0
SRS 106 D PA 1 6,0 - 20 30 27 36 1,0
SRS 108 D PA 1 8,0 5/16" 20 30 27 36 1,0
SRS 109.5 D PA 1 9,5 3/8" 20 30 27 36 1,0
SRS 110 D PA 1 10,0 - 20 30 27 36 1,0
SRS 112 D PA 1 12,0 - 20 30 27 36 1,0
SRS 212.7 D PA 2 12,7 1/2" 29 30 26 53 1,2
SRS 213.5 D PA 2 13,5 - 29 30 26 53 1,2
SRS 214 D PA 2 14,0 - 29 30 26 53 1,2
SRS 215 D PA 2 15,0 - 29 30 26 53 1,2
SRS 216 D PA 2 16,0 5/8" 29 30 26 53 1,2
SRS 217.2 D PA 2 17,2 - 29 30 26 53 1,2
SRS 218 D PA 2 18,0 - 29 30 26 53 1,2
SRS 319 D PA 3 19,0 3/4" 36 30 37 67 1,6
SRS 320 D PA 3 20,0 - 36 30 37 67 1,6
SRS 321.3 D PA 3 21,3 - 36 30 37 67 1,6
SRS 322 D PA 3 22,0 - 36 30 37 67 1,6
SRS 325 D PA 3 25,0 1" 36 30 37 67 1,6
SRS 426.9 D PA 4 26,9 - 45 30 42 82 2,0
SRS 428 D PA 4 28,0 - 45 30 42 82 2,0
SRS 430 D PA 4 30,0 - 45 30 42 82 2,0
SRS 532 D PA 5 32,0 1.1/4" 56 30 54 106 2,0
SRS 533.7 D PA 5 33,7 - 56 30 54 106 2,0
SRS 535 D PA 5 35,0 - 56 30 54 106 2,0
SRS 538 D PA 5 38,0 1.1/2" 56 30 54 106 2,0
SRS 542 D PA 5 42,0 - 56 30 54 106 2,0

Order hints

1 piece = 2 halves of clamp

Disclaimer

Despite careful checking, we cannot guarantee the accuracy of all information included on this site, and we accept no liability.
All data and information in our online catalogue are based on currently valid standards and the regulations from the employer's liability insurance association. Product safety can only be guaranteed when our assembly instructions are carefully observed. Non-adherence to these regulations can affect product operation and functioning and result in a loss of warranty. Our warranty is only valid for HANSA-FLEX products. Our products are constantly subject to further development and technical changes are therefore possible.