TS

Rod seal TS



Properties

Application Hydraulics
Design Rod U-ring
Media Mineral oils
Material PUR
Installation in closed grooves in open installation spaces, in open grooves B
Operating pressure up to 400 bar

Description

High abrasion resistance.
Extremely good sealing effect at low pressure.
Fast alternation of loads.

Hints

Clearance:
pressure = 50 bar / e= d < 60 <0.40 / e= d > 60 <0.50
Pressure= 100 bar / e= d < 60 <0.30 / e= d > 60 <0.40
Pressure = 300 bar / e= d < 60 <0.15 / e= d > 60 <0.20
Pressure = 400 bar / e= d < 60 <0.10 / e= d > 60 <0.15
Tolerance: d= H8 / f7; D= +/- 0.04; L= +0.4 / 0

Article Table

Product Name d mm D mm L mm
Product Name d mm D mm L mm
TS 12 18 12 18,0 5,0
TS 16 22 16 22,0 4,5
TS 16 24-1 16 24,0 7,0
TS 18 25 18 25,0 5,7
TS 20 25 20 25,0 3,5
TS 20 25-1 20 25,0 4,5
TS 20 26 20 26,0 6,0
TS 20 27 20 27,0 6,5
TS 20 30 20 30,0 8,0
TS 20 30-1 20 30,0 9,0
TS 20 30-2 20 30,0 11,0
TS 21 27 24 27,0 5,0
TS 22 28 22 28,0 5,0
TS 22 30 22 30,0 8,0
TS 22 32-1 22 32,0 9,0
TS 24 30 24 30,0 5,0
TS 25 32 25 32,0 5,0
TS 25 35 25 35,0 6,0
TS 25 35-2 25 35,0 10,0
TS 25 35-5 25 35,0 11,0
TS 25 36 25 36,0 6,0
TS 30 38 30 38,0 9,0
TS 30 40-1 30 40,0 8,0
TS 32 40 32 40,0 9,0
TS 32 42-1 32 42,0 9,0
TS 32 42-2 32 42,0 11,0
TS 35 43-1 35 43,0 9,0
TS 35 45 35 45,0 8,0
TS 36 44 36 44,0 9,0
TS 38 45 38 45,0 7,0
TS 40 50 40 50,0 7,0
TS 42 53 42 53,0 10,0
TS 45 53-1 45 53,0 7,0
TS 45 53 45 53,0 9,0
TS 46 54 46 54,0 9,0
TS 50 62 50 62,0 11,0
TS 56 66-1 56 66,0 7,5
TS 56 66 56 66,0 11,0
TS 60 70-3 60 70,0 13,0
TS 61 69 61 69,0 9,0
TS 63 71 63 70,0 9,0
TS 66 80 66 80,0 11,0
TS 68 76 68 76,0 9,0
TS 70 80 70 80,0 8,0
TS 70 80-2 70 80,0 13,0
TS 72 78 72 78,0 7,0
TS 76 84 76 84,0 9,0
TS 85 97 85 97,0 9,5
TS 88 96 88 96,0 9,0
TS 90 96 90 96,0 5,5
TS 90 100 90 100,0 7,5
TS 91 99 91 99,0 9,0
TS 107 115 107 115,0 9,0
TS 126 134 126 134,0 9,0
TS 145 153 145 153,0 9,0
TS 147 155 147 155,0 11,0
TS 175 183 175 183,5 9,0
TS 221 229 221 229,5 13,0

Order hints

We are able to produce seals with diameters of 20 to 510 mm with short lead times.

Disclaimer

Despite careful checking, we cannot guarantee the accuracy of all information included on this site, and we accept no liability.
All data and information in our online catalogue are based on currently valid standards and the regulations from the employer's liability insurance association. Product safety can only be guaranteed when our assembly instructions are carefully observed. Non-adherence to these regulations can affect product operation and functioning and result in a loss of warranty. Our warranty is only valid for HANSA-FLEX products. Our products are constantly subject to further development and technical changes are therefore possible.