TS LA

Rod seal TS-LA



Properties

Application Hydraulics
Design Rod U-ring
Media Mineral oils
Material (1) Seal: PUR, (2) Support ring: acetal resin / PTBR
Installation in closed grooves A, in open grooves B
Operating pressure up to 500 bar

Description

High abrasion resistance.
Extremely good sealing effect at low pressure.
Fast alternation of loads.

Hints

Clearance:
Pressure = 50 bar / e= d < 60 <0.60 / e= d > 60 <0.80
Pressure = 100 bar / e= d < 60 <0.60 / e= d > 60 <0.80
Pressure = 200 bar / e= d < 60 <0.40 / e= d > 60 <0.60
Pressure = 300 bar / e= d < 60 <0.30 / e= d > 60 <0.40
Pressure = 400 bar / e= d < 60 <0.20 / e= d > 60 <0.30
Pressure = 500 bar / e= d < 60 <0.10 / e= d > 60 <0.15
Tolerance: d= H8 / f7; D= +/- 0.04; L= +0.4 / 0

Article Table

Product Name d mm D mm L mm
Product Name d mm D mm L mm
TS 40 48-LA 40 48 9,0
TS 40 50-LA1 40 50 11,0
TS 40 52-LA 40 52 11,0
TS 40 55-LA 40 55 8,5
TS 40 55-LA1 40 55 11,0
TS 45 55-LA1 45 55 11,0
TS 45 60-LA 45 60 11,0
TS 50 60-LA1 50 60 11,0
TS 50 65-LA 50 65 11,0
TS 55 65-LA1 55 65 11,0
TS 56 71-LA 56 71 12,5
TS 60 70-LA4 60 70 13,5
TS 60 75-LA 60 75 13,0
TS 60 80-LA 60 80 13,0
TS 63 75-LA 63 75 13,0
TS 63 78-LA1 63 78 12,5
TS 63 78-LA 63 78 13,5
TS 63 83-LA 63 83 13,0
TS 65 75-LA 65 75 13,0
TS 65 80-LA 65 80 12,5
TS 70 85-LA1 70 85 13,0
TS 75 90-LA 75 90 13,0
TS 75 95-LA 75 95 14,5
TS 80 88-LA 80 88 10,0
TS 80 95-LA 80 95 12,5
TS 80 96-LA 80 96 10,5
TS 80 100-LA 80 100 12,5
TS80 100-LA1 80 100 14,5
TS 90 105-LA2 90 105 9,5
TS 90 105-LA1 90 105 13,0
TS 90 110-LA 90 110 13,0
TS 95 115-LA 95 115 14,5
TS 100 110-LA 100 110 13,5
TS 100 113-LA 100 113 13,5
TS 100 120-LA 100 120 14,5
TS 110 120-LA 110 120 14,5
TS 110 125-LA1 110 125 13,0
TS 120 140-LA 120 140 12,5
TS 140 165-LA 140 165 19,0

Order hints

We are able to produce seals with diameters of 20 to 510 mm with short lead times.

Disclaimer

Despite careful checking, we cannot guarantee the accuracy of all information included on this site, and we accept no liability.
All data and information in our online catalogue are based on currently valid standards and the regulations from the employer's liability insurance association. Product safety can only be guaranteed when our assembly instructions are carefully observed. Non-adherence to these regulations can affect product operation and functioning and result in a loss of warranty. Our warranty is only valid for HANSA-FLEX products. Our products are constantly subject to further development and technical changes are therefore possible.