Properties

Design Double guide ring
Installation insert into the groove
Material acetal resin + glass fibre
Media Mineral oil
Sliding speed max. 5.0 m/s
Surface pressure at 20°C 15 N/mm2; at 100°C 10 N/mm3
Temp. max. 110 °C
Temp. min. -30 °C

Description

Easy working of the fitting groove and assembly.
High load-bearing capacity.
Low coefficient of wear and low coefficient of friction (between 0.05 and 0.1) available in many sizes.

Hints

Calculation of shear force; F= p x D x L x n
F= maximum shear force (N)
p = maximum surface pressure (N/mm2)
D x L= projected area (mm2)
n= quantity of rings

Article Table

Product Name D mm d mm L mm D mm
Product Name D mm d mm L mm D mm
WR 16-0 19.1 16 4.0 -
WR 20 - 20 5.6 25
WR 20-1 - 20 9.7 25
WR 22 27.0 22 5.6 -
WR 22-1 27.0 22 9.7 -
WR 25-1 - 25 9.7 30
WR 27 - 27 5.6 32
WR 30 - 30 5.6 35
WR 25 30.0 25 5.6 -
WR 30-1 - 30 9.7 35
WR 27-1 32.0 27 9.7 -
WR 32 - 32 5.6 37
WR 28 33.0 28 5.6 -
WR 35 - 35 5.6 40
WR 35-1 - 35 9.7 40
WR 36-1 - 36 9.7 41
WR 28-1 33.0 28 9.7 -
WR 32-1 37.0 32 9.7 -
WR 40 - 40 5.6 45
WR 40-1 - 40 9.7 45
WR 36 41.0 36 5.6 -
WR 45 - 45 5.6 50
WR 40-2 45.0 40 15.0 -
WR 45-1 - 45 9.7 50
WR 50 - 50 5.6 55
WR 43 48.0 43 5.6 -
WR 50-1 - 50 9.7 55
WR 45-2 50.0 45 15.0 -
WR 55-1 - 55 9.7 60
WR 56-1 - 56 9.7 61
WR 47 52.0 47 5.6 -
WR 47-1 52.0 47 9.7 -
WR 58 - 58 5.6 63
WR 50-2 55.0 50 15.0 -
WR 63 - 63 5.6 68
WR 55 60.0 55 5.6 -
WR 56 61.0 56 5.6 -
WR 58-1 - 58 9.7 63
WR 63-1 - 63 9.7 68
WR 60 - 60 5.6 65
WR 60-1 - 60 9.7 65
WR 60-2 65.0 60 15.0 -
WR 65 - 65 5.6 70
WR 65-1 - 65 9.7 70
WR 67 - 67 5.6 75
WR 67-1 72.0 67 9.7 -
WR 70 - 70 5.6 75
WR 70-1 - 70 9.7 75
WR 70-2 75.0 70 15.0 -
WR 70-3 75.0 70 20.0 -
WR 75 - 75 5.6 80
WR 75-1 - 75 9.7 80
WR 72-1 77.0 72 9.7 -
WR 80-1 - 80 9.7 85
WR 75-2 80.0 75 15.0 -
WR 80-2 85.0 80 15.0 -
WR 85 - 85 5.6 90
WR 85-1 - 85 9.7 90
WR 80 85.0 80 5.6 -
WR 83-2 88.0 83 15.0 -
WR 85-2 90.0 85 15.0 -
WR 95 - 95 5.6 100
WR 90-1 - 90 9.7 95
WR 95-1 - 95 9.7 100
WR 90 95.0 90 5.6 -
WR 92-4 97.0 92 25.0 -
WR 95-2 100.0 95 15.0 -
WR 100-2 105.0 100 15.0 -
WR 100 105.0 100 5.6 -
WR 100-1 105.0 100 9.7 -
WR 105-2 110.0 105 15.0 -
WR 105-1 110.0 105 9.7 -
WR 110-2 115.0 110 15.0 -
WR 110-1 115.0 110 9.7 -
WR 115-1 120.0 115 9.7 -
WR 120-2 125.0 120 15.0 -
WR 120 125.0 120 5.6 -
WR 120-1 - 120 9.7 125
WR 125-2 130.0 125 15.0 -
WR 135-2 140.0 135 15.0 -
WR 155-2 160.0 155 15.0 -
WR 195-2 200.0 195 15.0 -

Order hints

We are able to produce guide rings with diameters of 20 to 510 mm with short lead times.

Disclaimer

Despite careful checking, we cannot guarantee the accuracy of all information included on this site, and we accept no liability.
All data and information in our online catalogue are based on currently valid standards and the regulations from the employer's liability insurance association. Product safety can only be guaranteed when our assembly instructions are carefully observed. Non-adherence to these regulations can affect product operation and functioning and result in a loss of warranty. Our warranty is only valid for HANSA-FLEX products. Our products are constantly subject to further development and technical changes are therefore possible.